Class P2 (ABEC 9) tolerances

Class P2 (ABEC 9) tolerances

Inner ring
d tΔdmp1) tΔds2) tVdsp tVdmp tΔBs tVBs tKia tSd tSia
All Normal Modified3)
> U L U L U L L
mm µm µm µm µm µm µm µm µm µm
2,5 10 0 –2,5 0 –2,5 2,5 1,5 0 –40 –250 1,5 1,5 1,5 1,5
10 18 0 –2,5 0 –2,5 2,5 1,5 0 –80 –250 1,5 1,5 1,5 1,5
18 30 0 –2,5 0 –2,5 2,5 1,5 0 –120 –250 1,5 2,5 1,5 2,5
30 50 0 –2,5 0 –2,5 2,5 1,5 0 –120 –250 1,5 2,5 1,5 2,5
50 80 0 –4 0 –4 4 2 0 –150 –250 1,5 2,5 1,5 2,5
80 120 0 –5 0 –5 5 2,5 0 –200 –380 2,5 2,5 2,5 2,5
120 150 0 –7 0 –7 7 3,5 0 –250 –380 2,5 2,5 2,5 2,5
150 180 0 –7 0 –7 7 3,5 0 –250 –380 4 5 4 5
Outer ring
D tΔDmp1) tΔDs2) tVDsp4)5) tVDmp4)5) tΔCs tVCs tKea tSD6) tSea
> U L U L
mm µm µm µm µm µm µm µm µm
18 30 0 –4 0 –4 4 2 Identical to

tΔBs
of an inner ring

of the same

bearing as the

outer ring

1,5 2,5 0,75 2,5
30 50 0 –4 0 –4 4 2 1,5 2,5 0,75 2,5
50 80 0 –4 0 –4 4 2 1,5 4 0,75 4
80 120 0 –5 0 –5 5 2,5 2,5 5 1,25 5
120 150 0 –5 0 –5 5 2,5 2,5 5 1,25 5
150 180 0 –7 0 –7 7 3,5 2,5 5 1,25 5
180 250 0 –8 0 –8 8 4 4 7 2 7

Tolerance symbols and definitions → table

  1. 1)
    These deviations apply for bearings in the 8 and 9 diameter series only.
  2. 2)
    These deviations apply for bearings in the 0 and 2 diameter series only.
  3. 3)
    Applies to inner rings and outer rings of bearings of matched bearing sets consisting of two or more bearings and universally matchable angular contact ball bearings.
  4. 4)
    No values have been established for capped bearings.
  5. 5)
    Applies to bearings prior to mounting and after removal of internal or external snap ring.
  6. 6)
    Tolerance values have become half the values in accordance with the revised ISO standard (2014) becauseSD is defined as perpendicularity of outer ring outside surface axis with respect to datum established from the outer ring face.

Contact us