Home » Technical » Tolerance symbols

Tolerance symbols

Loyal bearings

Tolerance symbol	Definition
	Radial bearings inner ring – cylindrical and tapered bore

d	Cylindrical bore: Nominal bore diameter Tapered bore: Nominal bore diameter at the theoretical small end
Δdmp	Cylindrical bore: Deviation of a mid-range size (out of two-point sizes) of bore diameter in any cross section from its nominal size Tapered bore: Deviation of a mid-range size (out of two-point sizes) of bore diameter at the theoretical small end from its nominal size
Δds	Deviation of a two-point size of bore diameter of a cylindrical bore from its nominal size
Vdsp	Range of two-point sizes of bore diameter in any cross section of a cylindrical or tapered bore
Vdmp	Range of mid-range sizes (out of two-point sizes) of bore diameter obtained from any cross section of a cylindrical bore
B	Nominal inner ring width
ΔBs Normal, Modified¹⁾	Symmetrical rings: Deviation of a two-point size of inner ring width from its nominal size Asymmetrical rings, upper limit: Deviation of a minimum circumscribed size of inner ring width, between two opposite lines, in any longitudinal section which includes the inner ring bore axis, from its nominal size Asymmetrical rings, lower limit: Deviation of a two-point size of inner ring width from its nominal size
VBs	Symmetrical rings: Range of two-point sizes of inner ring width Asymmetrical rings: Range of minimum circumscribed sizes of inner ring width, between two opposite lines, obtained from any longitudinal section which includes the inner ring bore axis
Kia	Circular radial run-out of inner ring bore surface of assembled bearing with respect to datum, i.e. axis, established from the outer ring outside surface
Sd	Circular axial run-out of inner ring face with respect to datum, i.e. axis, established from the inner ring bore surface
Sia	Circular axial run-out of inner ring face of assembled bearing with respect to datum, i.e. axis, established from the outer ring outside surface


	Radial bearings inner ring – tapered bore only

d₁	Nominal bore diameter at the theoretical large end of a tapered bore
Δd1mp	Deviation of a mid-range size (out of two-point sizes) of bore diameter at the theoretical large end from its nominal size
SL	Taper slope, the difference between nominal diameters at the theoretical large end and small end of a tapered bore (d₁ – d)
ΔSL	Deviation of taper slope of a tapered inner ring bore from its nominal size


	Radial bearings outer ring

D	Nominal outside diameter
ΔDmp	Deviation of a mid-range size (out of two-point sizes) of outside diameter in any cross section from its nominal size
ΔDs	Deviation of a two-point size of outside diameter from its nominal size
VDsp	Range of two-point sizes of outside diameter in any cross section
VDmp	Range of mid-range sizes (out of two-point sizes) of outside diameter obtained from any cross section
C	Nominal outer ring width
ΔCs Normal, Modified¹⁾	Symmetrical rings: Deviation of a two-point size of outer ring width from its nominal size Asymmetrical rings, upper limit: Deviation of a minimum circumscribed size of outer ring width, between two opposite lines, in any longitudinal section which includes the outer ring outside surface axis, from its nominal size Asymmetrical rings, lower limit: Deviation of a two-point size of outer ring width from its nominal size
VCs	Symmetrical rings: Range of two-point sizes of outer ring width Asymmetrical rings: Range of minimum circumscribed sizes of outer ring width, between two opposite lines, obtained from any longitudinal section which includes the outer ring outside surface axis
Kea	Circular radial run-out of outer ring outside surface of assembled bearing with respect to datum, i.e. axis, established from the inner ring bore surface
SD	Perpendicularity of outer ring outside surface axis with respect to datum established from the outer ring face
Sea	Circular axial run-out of outer ring face of assembled bearing with respect to datum, i.e. axis, established from the inner ring bore surface


	Chamfer limits

r_s	Single chamfer dimension
r_{s min}	Smallest single chamfer dimension of r_s, r₁, r₂, r₃, r₄ …
r₁, r₃	Radial direction chamfer dimensions
r₂, r₄	Axial direction chamfer dimensions


	Thrust bearings shaft washer

d	Nominal bore diameter of shaft washer, single direction bearing
Δds	Deviation of a two-point size of shaft washer bore diameter from its nominal size
Δdmp	Deviation of a mid-range size (out of two-point sizes) of shaft washer bore diameter in any cross section from its nominal size
Vdsp	Range of two-point sizes of shaft washer bore diameter in any cross section
d₂	Nominal bore diameter of central shaft washer, double direction bearing
Δd2mp	Deviation of a mid-range size (out of two-point sizes) of central shaft washer bore diameter in any cross section from its nominal size
Vd2sp	Range of two-point sizes of central shaft washer bore diameter in any cross section
B1s	Height of a shaft washer of a bearing specifically manufactured for paired mounting
ΔB1s	For bearings specifically manufactured for paired mounting: Upper limit: Deviation of a minimum circumscribed size of shaft washer height, between two opposite lines, in any longitudinal section which includes the shaft washer bore axis, from its nominal size Lower limit: Deviation of a two-point size of shaft washer height from its nominal size
Si	Range of two-point sizes of thickness between shaft washer raceway and the back face, cylindrical roller thrust bearing Range of minimum spherical sizes between the raceway and the opposite back face of the shaft washer, obtained from any longitudinal section which includes the shaft washer bore axis, thrust ball bearing


	Thrust bearings housing washer

D	Nominal outside diameter of housing washer
ΔDs	Deviation of a two-point size of housing washer outside diameter from its nominal size
ΔDmp	Deviation of a mid-range size (out of two-point sizes) of housing washer outside diameter in any cross section from its nominal size
VDsp	Range of two-point sizes of housing washer outside diameter in any cross section
C1s	Height of a housing washer of a bearing specifically manufactured for paired mounting
ΔC1s	For bearings specifically manufactured for paired mounting: Upper limit: Deviation of a minimum circumscribed size of housing washer height, between two opposite lines, in any longitudinal section which includes the housing washer outside surface axis, from its nominal size Lower limit: Deviation of a two-point size of housing washer height from its nominal size
Se	Range of two-point sizes of thickness between housing washer raceway and the back face, cylindrical roller thrust bearing Range of minimum spherical sizes between the raceway and the opposite back face of the housing washer, obtained from any longitudinal section which includes the housing washer outside surface axis, thrust ball bearing


	Thrust bearings assembled bearing height

T	Nominal assembled bearing height, single direction thrust bearing
ΔTs	Deviation of minimum circumscribed size of assembled bearing height from its nominal size, single direction thrust bearing
T₁	Nominal assembled bearing height, double direction thrust bearing
ΔT1s	Deviation of minimum circumscribed size of assembled bearing height from its nominal size, double direction thrust bearing
2C	Total nominal height of outer rings of assembled bearing, double direction thrust bearing
H	Nominal assembled bearing height, axial-radial cylindrical roller bearing
ΔHs	Deviation of minimum circumscribed size of assembled bearing height from its nominal size, axial-radial cylindrical roller bearing
H1	Nominal assembled bearing sub-assembly height, axial-radial cylindrical roller bearing
ΔH1s	Deviation of minimum circumscribed size of assembled bearing sub-assembly height from its nominal size, axial-radial cylindrical roller bearing


	Cartridge units

ΔD2s	Deviation of a two-point size of cartridge housing seat diameter from its nominal size

1)
Modified applies to inner rings and outer rings of bearings of matched bearing sets consisting of two or more bearings and universally matchable angular contact ball bearings.

Technical

Support/Inquiries